Ethernet Network Contact Closure Remote SPDT Relay Controller 4-Channel 1-Way
Please note that images above may contain product not included with purchase.
Highlights
- Transmitter Includes 4 Contact Closure Inputs
- Receiver Includes 4-Channel SPDT Relays
- Sold in Pairs and Uses 12VDC per Controller
- LAN Operation Utilizing Static IP Address Assignment
- Transmitter Communicate using 2-Way Communications
- Transmitter Controls Remote Relays
- Receiver Displays Status of Remote Relays
- Simple Configuration
- Relay and Communication LED Status Lights
Ethernet Contact Closure 1-Way Transmitter Receiver Pair
Our MirC 4-Channel SPDT Relay Controllers are manufactured in pairs, designed to work together when powered up using Ethernet communications over a local area network. The contact closure inputs on the transmitter control relays on the remote receiver. Both the transmitter and receiver display the status of the relays using LEDs. MirC controllers consist of custom firmware that keeps this married pair of controllers in constant communications with each other.
This pair of MirC controllers is equipped with your choice of 5-Amp or 10-Amp SPDT relays, ideal for use in most general purpose switching applications. Ideal for lights, small motors, gate openers, and much more. On-board Relay status LEDs and busy/ready LEDs let you know when these controllers are talking to each other.
Important Change Notice
This Device no-longer communicates over the internet due to changes in technology. Please contact us for a internet connected solution if required.
MirC Controllers Mirror Contact Closures in a Remote Location. A contact closure input is transmitted over a Ethernet network and transmitted to a remote relay controller also equipped with a Ethernet connection, which provides a remote contact closure output.
Ethernet MirC Remote Contact Closure Transmitter and Receiver Controllers
Contact Closure Inputs in one location control remote relays in a remote location using Ethernet network communications. Mirror controllers are paired during initial configuration, ensuring peaceful co-existence on your network. MirC controllers stay connected to each other using Ethernet network communications. Inputs on the transmitting controller activate the relays on the receiving controller. The Ethernet interface supports DHCP as well as static IP addresses (IPv4). For used in a Local Area Network only (not for use over the internet).
Permanently Married
MirC is Always Trying to Talk to it’s Mate!
MirC controllers are always talking to each other. They stay in relentless communications for optimal reliability. Should they lose communication with each other, they will keep calling out for each other until they find their mate.
Syncing Up
MirC controllers are equipped with contact closure inputs on the transmitter and relay outputs on the receiver. The inputs on the transmitter activate the relays on the remote receiver using Ethernet network communications. The transmitter displays the status of the remote relays using LEDs (one LED per relay), so both the transmitter and receiver include relay status! Every MirC controller is equipped with a Busy/Ready LED. If the Busy LED flashes, this indicates the remote device has successfully received and accepted your contact closure status. If the Busy LED does not flash, the remote device is not properly connected.
Beacon Mode
Beacon Mode communicates with a Remote MirC controller many times per second, refreshing Relay Status information every time a valid data stream is received by the remote device. Relays are only refreshed when a valid data packet is received. If data is lost, the Ready LED will stay on and Relays will stay in their current state. If the remote MirC controller is in range, the Busy LED will flash periodically, indicating valid communications between devices. Beacon Mode is slower than Smart Mode and is used primarily for initial testing of two devices.
Smart Mode
Once you have determined an installation location for both MirC controllers, move the Beacon/Smart jumper to the Smart position. Smart Mode communicates to the remote device any time a change is detected on the local device. Otherwise, the controller periodically checks to make sure the remote device is communicating. Smart Mode is significantly faster than Beacon Mode. Smart Mode is the preferred mode for daily use in most applications. Note that each MirC controller can be set to a different mode and jumper changes take effect immediately. Again, the Busy LED will indicate the remote device is properly communicating. Smart Mode will also verify the relays on the remote device are properly set. If they are not, Smart Mode will attempt communications until the remote device responds. If communications is lost between the MirC controllers, all relays will automatically shut off within 30 seconds. If this is not desirable, Beacon Mode should be used.
Beacon Mode vs. Smart Mode
Perhaps the most notable difference between Beacon and Smart Mode is how relays respond if communication is lost. In Beacon Mode, the relays will stay in their current state and will not change unless a new data packet is received. In Smart Mode, relays will turn off automatically in 10 to 30 seconds if communications is lost between MirC controllers.
Applications
MirC controllers are typically used by our large industrial clients for a wide range of remote control switching applications. Typical installations include remote gate operation, remote light control, remote pump control, as well as various temperature override applications. MirC controllers are typically used instead of expensive trenching and drilling applications where running wire can be destructive and sometimes cost prohibitive. MirC is commonly used in signage applications that may require a warning light as a supplement to a standard traffic light. MirC is also used by our customers to provide remote operation of lights, doors, gates, motors, pumps, and valves.
Other Mirror Family Controllers
- MirX consists of relays and contact closure inputs on each controller (local and remote). Inputs in the home location control the relays in the remote location. Inputs in the remote location control the relays in the home location.
- MirC is the same as MirX except MirC consists of contact closures on one controller and relays on the remote controller.
- MirW consists of several contact closure input boards and a single relay controller. All remote contact closure inputs are used to control local relays.
MirC Variations
NCD manufactures several variations of MirC as well as other Mirror series devices. Here are some variations you may wish to consider:
- MirC Wireless for remote control applications with Wireless Encryption
- MirC Wired for hard-wired communication applications
- MirC Network for local area Ethernet communications in a Local Area
Relay Options
MirC offers several relay options, depending on your application. We stock solid-state, high-power, and general purpose relays in our MirC line of products. However, we can customize our MirC controllers to your exact needs. Please contact us if you need any custom designed MirC controllers, including different relay types or firmware modifications. This particular controller has the following relay options available:
Associated Part Numbers
This product may have been previously manufactured using a part number shown below:
Relay Options
10-Amp SPDT Signal Relay Option
This controller is available with a 10-Amp relay option, allowing control of higher-power loads up to an absolute maximum of 240VAC at 10 Amps. Ideal for general purpose switching applications, this relays is focused on power-switching, and should never be used for low-power signals due to a higher On resistance of up to 150 Ohms when relay contacts are new (contact resistance drops to less than 1 Ohm after break-in period). The 10-Amp relay is of the SPDT variety, which provides Common (C), Normally Open (NO), and Normally Closed (NC) connections. Common is connected to NC when the relay is off. Common disconnects from NC and connects to NO when the relay is activated. All connections are made via screw terminals, capable of accepting up to 12 AWG wire. Review Datasheet
5-Amp SPDT Signal Relay Option
This controller is available with a 5-Amp relay option, allowing control of higher-power loads up to an absolute maximum of 240VAC at 5 Amps. Ideal for general purpose switching applications, this relays is focused on power-switching, and should never be used for low-power signals due to a higher On resistance of up to 150 Ohms when relay contacts are new (contact resistance drops to less than 1 Ohm after break-in period). The 5-Amp relay is of the SPDT variety, which provides Common (C), Normally Open (NO), and Normally Closed (NC) connections. Common is connected to NC when the relay is off. Common disconnects from NC and connects to NO when the relay is activated. All connections are made via screw terminals, capable of accepting up to 12 AWG wire. Review Datasheet
Mechanical Drawing
Wiring Diagrams
Point to Point Wireless Switching
Our MirC Point to Point Switching series is the ultimate in easy and reliable remote relay control. A contact closure in one location trigger the corresponding relay in another location on a married pair. No wires, no software, it just works. This contact closure can be a simple switch, or any sensor that outputs a contact closure such as some current sensors and most proximity sensors.
MirC Vid Internet
Our MirC Point to Point Ethernet Switching series is the ultimate in easy and reliable remote relay control. A contact closure in one location trigger the corresponding relay in another location on a married pair. No wires, no software, it just works. This married pair can be located anywhere in the world as long as the network they are connected to have internet access. Additionally they can work on a LAN without internet access provided they are on the same network. This contact closure can be a simple switch, or any sensor that outputs a contact closure such as some current sensors and most proximity sensors.
Introduction to Relay Control
This video will guide you in determining which relay controller you need for your application as well as a general overview of the differences between Relay Options. If you’re new to our products or just need a refresher for a new application this is a great place to start.
Induction Suppression
Learn about Induction and how it comes into play with Relay Controllers. Induction suppression can make your Relay Control applications intermittent and unreliable. This video will show you what causes it, how to avoid it, and how to account for it in your application.
Transmitter Controller Specifications
This table covers all NCD MirC Transmitter Controllers. All ratings assume 12VDC operation at 70°F (21°C). Please note that most ratings are estimated and may be subject to periodic revision. Some ratings represent stock controller settings without performance enhancement optimizations. The specifications provided below are for power budgeting purposes only and may not represent real-world measured values.| Specifications of NCD SPDT Relay Controllers | Minimum | Nominal | Maximum | Notes |
|---|---|---|---|---|
| Operational Voltages | 10VDC | 12VDC | 15VDC | |
| Standby Power Consumption | 35mA | 100mA | 200mA | |
| Operational Temperature Range | -40°F (-40°C) | 70°F (21°C) | 185°F (85°C) | Theoretical Component Limits Shown |
| Storage Temperature Range | -67°F (-55°C) | 70°F (21°C) | 185°F (85°C) | Theoretical Component Limits Shown |
| Operational Ambient Air Humidity | 0% | 50% | 70% | Non-Condensing Humidity Values Shown |
SPDT Relay Controller Specifications
This table covers all NCD SPDT Relay Controllers. All ratings assume 12VDC operation at 70°F (21°C). Please note that most ratings are estimated and may be subject to periodic revision. Some ratings represent stock controller settings without performance enhancement optimizations. The estimated processing time can be impacted by background services and choice of commands. Standby power consumption assume no communications module is installed and no relays are active on the controller. Please add the power consumption of the activated relays and communications module to obtain a better estimation of power consumption.| Specifications of NCD SPDT Relay Controllers | Minimum | Nominal | Maximum | Notes |
|---|---|---|---|---|
| Operational Voltages | 10VDC | 12VDC | 15VDC | |
| Standby Power Consumption | 35mA | 100mA | 200mA | No Active Relays, No Com Module |
| Relay Power Consumption | 28mA | 35mA | 60mA | Consumption of Each Activated Relay |
| Operational Temperature Range | -40°F (-40°C) | 70°F (21°C) | 185°F (85°C) | Theoretical Component Limits Shown |
| Storage Temperature Range | -67°F (-55°C) | 70°F (21°C) | 185°F (85°C) | Theoretical Component Limits Shown |
| Operational Ambient Air Humidity | 0% | 50% | 70% | Non-Condensing Humidity Values Shown |
| Relay Activation Time | 4ms | 5ms | 10ms | Needs Further Validation |
| Relay Deactivation Time | 5mS | 10mS | 15mS | Needs Further Validation |
Communication Module Specifications
This table covers all NCD Communication Modules. While NCD communication modules operate at 3.3VDC, the ratings below highlight the effect they will have on the master controller operating at 12VDC at 70°F (21°C). Maximum ratings should be used for power budget planning purposes and may reflect short term absolute maximum peak current consumption. Some ratings are estimated and subject to periodic revision.| Specifications of NCD Communication Modules | Minimum | Nominal | Maximum | Notes |
|---|---|---|---|---|
| Operational Temperature Range | -40°F (-40°C) | 70°F (21°C) | 185°F (85°C) | Theoretical Component Limits Shown |
| Storage Temperature Range | -67°F (-55°C) | 70°F (21°C) | 185°F (85°C) | Theoretical Component Limits Shown |
| Operational Ambient Air Humidity | 0% | 50% | 70% | Non-Condensing Humidity Values Shown |
| USB Communications Module Power Consumption | NA | NA | NA | USB Modules are Powered by the USB Port Do Not Consume Device Current |
| RS-232 Communications Module Power Consumption | 10mA | 20mA | ||
| RS-485 Communications Module Power Consumption | 20mA | 35mA | ||
| Ethernet Communications Module Power Consumption | 58mA | 82mA | 100mA | |
| WiFi Bluetooth USB Communications Module Power Consumption | 37mA | 50mA | 100mA | Up to 300 Foot Indoor Wireless Range, Unobstructed. Up to 50 Foot Range Through Walls. |
| 900MHz Wireless Communications Module Power Consumption | 13mA | 30mA | 50mA | Up to 1,000 Foot Indoor Wireless Range, up to 2 Mile Outdoor Wireless Range using Included Antennas. Up to 28 Miles Outdoor Wireless Range using High-Gain Antennas. |
| 868MHz Wireless Communications Module Power Consumption | 17mA | 30mA | 50mA | |
| 2.4GHz Wireless Communications Module Power Consumption | 8mA | 20mA | 30mA | |
| KFX Wireless Key Fob Communications Module Power Consumption | 11mA | 15mA | 25mA | Up to 200 Feet Outdoor Wireless Range using 1, 2, 3, 4, or 5 Button Key Fobs. Up to 700 Feet Outdoor Wireless Range using 8-Button Remotes. |
Notes
MirC devices are only sold as a permanently married pair, pricing shown on our web site indicates pricing for the pair of controllers. Contact Closure Inputs may only be connected to switches, buttons, or sensors with Contact Closure capability. Not suitable for use in voltage detection applications. MirC devices use the Lantronix XPort Pro with custom firmware. Data is transacted using two-way communications to ensure the remote device is properly functioning. The Busy LED is always used to indicate a properly functioning remote device. If you do not see the Busy LED flash, then the MirC controller is unable to communicate to the remote device. A flashing busy LED is your verification that all communications are functioning properly between MirC controllers.
Customers who require inductive switching (such as motors, lights, pumps, solenoids, and Transformers) should visit the Induction Suppression portion of our web site.
No Voltage Input
Please Note: Users must NEVER apply any voltage to an input on the MirC controller, these inputs are for Contact Closure connections only.
No Voltage Output
Please Note: Relays provide a contact closure output. They do not provide a voltage output. On-Board relays will switch a voltage that is provided externally by the user.
Ethernet TCP/IP Compatibility Notes
This device periodically sends UDP Packets on port 13,000, which help identify the IP address of this device on your network.